- #Sony wireless headset volume reset how to#
- #Sony wireless headset volume reset registration#
- #Sony wireless headset volume reset Bluetooth#
Release your fingers within 5 seconds after the indicator starts flashing. NOTE: This will cause the indicator (red) of the charging case flashing. Hold your fingers to the touch sensors on both the left and right units for about 10 seconds.
#Sony wireless headset volume reset Bluetooth#
Connect and pair with a Bluetooth device, then check to see if the issue was resolved. Place the headset into the charging case. Delete the pairing information for the headphones from the device and then pair them again. The indicators (blue) flash 4 times, and the headphones are initialized. Release your fingers when the indicators (red) of the headphones start flashing. Place the headphones in the charging case, leave the lid of the charging case open, then hold your fingers to the touch sensors on both the left and right units for about 10 seconds. Initializing the headset to restore factory settings #Sony wireless headset volume reset how to#
Tip: Learn how to turn captions on or off when watching Internet videos from YouTube Note: You can also see how to reset in this video:
Check to see if the issue is resolved after resetting. The indicator (red) light may be lit after the reset is finished. If the indicator (red) did not flash in Step 3, you may need to hold your finger to the touch sensor on the right side of the headphones for about 30 seconds. Hold your finger to the touch sensor on the right unit for about 20 seconds. You may be able to continue even if the indicator (red) does not flash. If the indicator (red) did not flash in Step 1, you may need to hold your finger to the touch sensor on the left side of the headphones for about 30 seconds. 
Release your finger when the indicator (red) of the headphones turns off after flashing. Turn off the headset while the USB Type-C cable is disconnected and then press and hold the (power) button and the - button simultaneously for 7 seconds or more. Place the headphones in the charging case, leave the lid of the charging case open, then hold your finger to the touch sensor on the left unit for about 20 seconds. Initializing the headset to restore factory settings If the headset does not operate correctly even after resetting, initialize the headset. Initializing the headset to restore factory settings. Check the Applicable Products and Categories section of this article before starting these steps. Do not put the headset back in the charging case before the initialization process is complete.IMPORTANT: This article applies only to specific products and/or operating systems. If you are not sure if the initialization process has completed, wait a few minutes and start over from step 1. When the indicator lights flash blue 4 times, the headset is initialized. Press the buttons on both the left and right units within 10 seconds after the indicator lights change to solid red. NOTE: This will cause the indicator lights to change from flashing to solid red. Release your fingers within 5 seconds after the indicator lights flash red. NOTE: While doing this, if the indicator lights flash blue, continue to hold the buttons until they flash red. Press and hold the buttons on both the left and right units of the headset until the indicator lights of the headset flash red (about 15 seconds). NOTE: After initializing the headset, you should also delete the headset pairing information from any connected devices and then pair them again. IMPORTANT: This operation resets all the device settings to the factory defaults and deletes all pairing information. Initialize the headset to restore factory settings 
If the headset does not operate correctly even after a reset, initialize the headset to restore the factory settings.
#Sony wireless headset volume reset registration#
During a reset, the device registration (pairing) information and other settings are retained.Press and hold the button on the right unit for about 20 seconds. Release your finger when the indicator light (red) of the headset flashes and turns off. Press and hold the button on the left unit for about 20 seconds. Initialize the headset to restore factory settings.About the sound quality mode Supported codecs About the DSEE Extreme function Making phone calls. Check the Applicable Products and Categories section of this article before starting these steps. Listening to ambient sound during music playback (Ambient Sound Mode) Listening to ambient sound quickly (Quick Attention Mode) Speaking with someone while wearing the headset (Speak-to-Chat) Sound quality mode. IMPORTANT: This article applies only to specific products and/or operating systems.
0 kommentar(er)
